VIPER Gen 3 & 4 (2003 - 2010)
PRODUCTS

Digital screen displays trouble codes and erases them in minutes. This reader will display live data including temperatures, timing, fuel pressure, engine load, Oxygen Sensors Readings, etc.!  Also displays complete code description - no need to look codes up in a code book!  Small enough to fit in your pocket.  This handy little tool can save a lot of headaches and quickly diagnoses what codes have been set in the PCM (Cars computer).
Saves time and money by allowing you to do it yourself.

 Reads and erases Diagnostic Trouble Codes (DTCs) of Engine, ABS, Airbags and Automatic Transmission
 Turns off check engine light
 Highly reliable and accurate
 Easy-to-read crystal-clear backlit 2-line LCD display
 Easy to use with one plug-in
 Stand-alone unit with no need for an additional laptop computer to operate
 Small in size and conveniently fits in your palm
 Performs continuous DTC scan
 Specially designed for DIYers
 Safely communicates with the on-board computer
 No batteries needed-power provided via OBD II cable
 Users manual contains VW/AUDI Diagnostic Trouble Code Definitions

Will not work on Vipers 1992-1995
 

1-2 week delivery

If you are having trouble ordering online: Please call us at 352 688 8160
 

$  6.95

We welcome our many Overseas Customers!
More Shipping Info Click Here

1-2 week
Delivery

If you are having trouble ordering online: Please call us at 352 688 8160
 

$  5.95

We welcome our many Overseas Customers!
More Shipping Info Click Here

This reader will display live data including temperatures, timing, fuel pressure, engine load, Oxygen Sensors Readings, etc.!  Also displays complete code description - no need to look codes up in a code book!
Even if you don't repair your vehicle yourself, knowing the Diagnostic Trouble Code number before taking the vehicle in for repair is good knowledge to have. Once the vehicle is repaired, the Diagnostic Trouble Code(s) can be erased and the Check Engine light turned off using this scan tool.

In areas that require a smog test, an illuminated Check Engine light fails the emission test, even if the repaired vehicle might otherwise pass inspection. This OBD II Scan Tool turns off the Check Engine light.
Another highly useful application for the scan tool is purchasing used vehicles. Used vehicles can have all sorts of expensive mechanical or electrical problems. Since our scanner is a portable device, the buyer can connect the scan tool to the vehicle and in a few seconds determine if the vehicle has detected a problem. Remember, not all Diagnostic Trouble Codes illuminate the Check Engine light and a scan tool is the only way to obtain the information.
Requires a 9 volt battery.

n Works with all 1996 and newer cars & trucks that are OBD II compliant
n Live Data Stream
n DTC (Diagnostic Trouble Codes) meanings are displayed in text mode
n Reads Freeze Frame Data
n Large Backlit LCD Display
n Large Database of Diagnostic Trouble Code(s)
n Clears / Turns off Check Engine Light
n Reads VIN number: great for verification of used cars!
n Tests I/M Status: Misfire Monitor, Fuel System, O2 System, EGR System, MIL Status
n Reads and clears generic and manufacture specific Diagnostic Trouble Codes (DTC)
n Supports multiple trouble code requests: generic codes, pending codes and manufacturer's specific codes
n Highly reliable and accurate
n Easy to read backlit LCD display
n Easy to use with one plug-in
n Safely communicates with the on-board computer
n Stand-alone unit with no need for an additional laptop computer to operate
n FULLY COMPATIBLE WITH CAN PROTOCOL
 

2 week delivery

If you are having trouble ordering online: Please call us at 352 688 8160
 

$  6.95

We welcome our many Overseas Customers!
More Shipping Info Click Here

• Set your ride up with most advanced technology in engine monitoring—the Edge Insight CS/CTS
• Choose between the Edge Insight CS or Insight CTS monitor
• The Insight CS (Color Screen) is a full-color, high-resolution 2.4” button-controlled screen
• Either monitor installs easily into your vehicle’s OBDII port
• View up to 8 different parameters from your ride’s engine in either analog or numeric style
• Parameters vary by vehicle year, make and model
• Scan tool displays diagnostic trouble codes, monitors peak speed and RPM values and records 0-60 and quarter-mile times
• Increase safety with user-defined visual and audible alerts
• Combine either monitor with other performance products to read vital engine data
• MyStyle software included for full customization of your CS or CTS monitor

Think you need to spend thousands of dollars to get in touch with your engine’s parameters? Think again! The Edge Insight CS and CTS monitors are the high-tech, standalone monitors which install right into your OBD-II port for immediate SAE data.

Choose between a full-color, high-resolution 2.4” button-controlled screen or a full-color, high-resolution 4.3” touch screen monitor. Both screens view up to 8 different engine parameters at a time. And, you can view outputs in numeric or analog style. However, your vehicle’s year, make and model determine which parameters are available.

The Edge Insight’s built-in digital gauge display scan tool captures and records information such as diagnostic trouble codes, peak speeds, RPMS and performance times, like 0-60 or quarter-mile times. Best yet, your Insight CS or CTS monitor is backed with a 1-year warranty.

• For use with 1996 and newer vehicles equipped with an OBDII port
• Monitors do not reprogram/tune or add power to vehicle

2 week delivery

If you are having trouble ordering online: Please call us at 352 688 8160
 

$  9.95

We welcome our many Overseas Customers!
More Shipping Info Click Here

This tune is done by the Worlds BEST Viper tuners!
Finally, the Viper SRT-10 owners have a means of flash-programming their Powertrain Control Modules to make changes in the way the engine systems operate or to correctly control aftermarket engine modifications without the need for piggyback or inline controllers, or going to a replacement controller. The capability of the factory PCM is greater than expected, and as of now, can finally be programmed by the end user easily and without so much as removing a single screw.

The flash programmers (XCal2) can hold a total of 3 tunes plus the stock tune. The end user can switch between these tunes any time they would like by plugging the controller into the OBD-2 port under the driver side dash. An SCT/DCX authorized dealer such as ours can edit these tunes at any time if the car is upgraded again, and now that the LiveLoad software has been released, these tunes can simply be e-mailed to and uploaded by the customer at home. The flash programmer will VIN lock to your car once it is used, although the programmer can be unlocked and moved to a different car for a fee if you happen to sell or change vehicles. The XCal2 can also read and erase DTC's to extinguish the check engine light and diagnose faults.

The purchase price includes 1 XCal2, and up to 3 basic tunes. Additional basic tunes can be added later, but are not required during the initial purchase and can be added at any later date for $49.95 each.  Our lab will work with the customer to determine what parameters will be changed, such as injector scaling, fan temps, spark and fuel maps, decel fuel modes, etc. YOU chose your parameters, or you can have us choose them for you. There is no hidden fee for custom tunes, each and every customer has the option to specify what they want in their tunes. Please contact us if you have any questions on what can be edited on your program. Large scale custom tuning also available for extremely modified engines, this is charged by the hour for writing tunes.

All these features make this device a "must have" for all GEN3 Viper owners.  Viper SRT10's from years 2004-2006 will also have an additional benefit of considerably faster 0-60mph times!

Select Below your Processor Code, this is the part number found on your PCM. If your code is not listed, please contact us it just needs to be added.
The PCMs on 2003-2006 Vipers are located on the Driver side inner fender, right behind the upper radiator hose and to the rear of the headlight. Also select the number of tunes you wish to start with, additional tunes can be added later.

This price includes one (1) advanced upgrade tune.  However, this device allows you to have up to three (3) custom tunes. Each additional tunes added is an additional $49.95.  We will need to know all the modifications to your Viper and what fuel you will be using.

Adding up to 30 rear wheel horsepower and 30 rear wheel torque has never been this easy and inexpensive! This SCT flash device allows quick and easy power upgrades by simply plugging it into your diagnostic computer port and downloading one of the low, medium or high performance custom tunes made The SCT XCalibrator 2 arrives to you with 1 performance tune, custom written and tested and includes- the skip shift feature turned off, disabled downstream O2 sensors for "off road" cat delete and programming to turn the fan on at 181 degrees versus the stock setting of 210 degrees. This versatile tool also allows the user to diagnose check engine lights and clear trouble codes. Your factory tune will never be lost either as the XCalibrator 2 has the ability to store it if you ever choose to go back to the factory settings. All these features make this device a "must have" for all GEN3 Viper owners. 

Example:  The following performance gains were recorded on our in-house dyno using 93 octane fuel : Rear Wheel HP / Rear Wheel Torque gains @ RPM are; 5 HP / 13 TQ @ 2,000 RPM, 6 HP / 13 TQ @ 2,500 RPM, 7 HP / 14 TQ @ 3,000 RPM, 20 HP / 30 TQ @ 3,500 RPM, 25 HP / 31 TQ @ 4,000 RPM, 30 HP / 35 TQ @ 4,500 RPM, 25 HP / 26 TQ @ 5,000 RPM, 12 HP / 11 TQ @ 5,500 RPM. These tunes were carefully created and tested to allow maximum performance without engine pinging.

NOTE : Please include your phone number so we may call you to get all the information we need.
 

*Removes your Top Speed Governor!
*Gets rid of  your Skip Shift!
*Your engine runs cooler!
*Faster Acceleration from start times!
...and so much more!!

Custom Tuned to your Viper Specifically!

*TO find PCM Processor Code:
PCMs on 2003-2006 cars are located on the Driver side inner fender, right behind the upper radiator hose and to the rear of the headlight.

We welcome our many Overseas Customers!
More Shipping Info Click Here